Stone in Architecture / Commercial

Maltese limestone anchors U.S. Embassy to community

September 1, 2011
KEYWORDS leed / limestone / Malta / stone
/ Print / Reprints /
ShareMore
/ Text Size+
Trans

Stationed in the middle of the Mediterranean Sea — directly south of Sicily and north of Libya — is Malta, a group of seven islands of which three are inhabited. The largest of the three is Malta. With low rocky terrain and sandy soil, the land is rich in limestone. Recently, a new U.S. Embassy compound was built in the island’s capital of Valletta — featuring an extensive showcase of stone, including Maltese limestone. The use of the local limestone not only reflects the style of the island’s existing architecture, but contributed to overall LEED certification.

Under contract with the U.S. Department of State, Bureau of Overseas Building Operations, the U.S. Embassy Compound was designed by Karn Charuhas Chapman & Twohey (KCCT) Architects of Washington, DC — a firm specializing in U.S. Embassy design. The project team included Principals John Chapman, AIA and Paul Phillips, AIA, LEED® AP, Project Designer Daniel Lavoie and Construction Administrator Shokouh Amin-Khalilian, LEED® AP, CDT.

“When we begin a design in a foreign country — especially ones we haven’t been to before — we team up with a local contractor and design firm,” explained Phillips. “We explore the country and look at the local surroundings to get a sense of the vernacular architecture. We visit the nicest buildings such as hotels, resorts, office buildings and talk to the property managers to see where their stone finishes originate from — find out if there are regional sources available.”

According to Phillips, stone represents the baseline of quality for U.S. Embassy designs. “Embassies should be portrayed as diplomatic facilities,” he said. “Stone represents the engagement of the U.S. Department of State and the designers to the permanence and timelessness of these diplomatic missions, as well as the U.S. commitment to diplomacy in these countries.”

“We have a stone consultant in Alicante, Spain who understands the different strengths, availability, cost and fabrication methods of stone around the world,” Phillips continued. “We consult with him on regionally available stone types and finishing techniques and he facilitates visits to fabricators for inspections and mock-ups.”

Choosing local limestone

From the start, the decision had been made to use local stone for the new U.S. Embassy compound, which consists of eight buildings, including the Chancery, three compound access control buildings and marine quarters as well as utility, warehouse and recreation facilities. While the tiered three-story Chancery is built of stone, the ancillary buildings are buff-colored stucco.

 “We wanted to use local stone from the beginning — not only because it is used in many buildings in Malta, but because we were aiming for high sustainability, with LEED in mind,” said Phillips. “We wanted to use stone from within a 500-mile radius. In Malta, we have a pretty good range of resources. We could have utilized stone from other countries, but we decided it made more sense to use the local limestone because of its beauty and locality.”

“Another good reason to have used regional and Maltese materials is because of the diplomatic nature of Embassies,” continued the architect. “It’s very nice when U.S. representatives discuss with local officials about the design, and they can say that it used local materials, local laborers and local methods of installation. The decision was made early on to use Franka Rockface limestone, [also called Maltese limestone], for the base of the building.”

Phillips explained that there are two primary types of regional limestone. “There is one on the great island of Malta, which is very soft, and one on the neighboring island of Gozo that is extremely dense and very hard, but doesn’t have the vibrant color,” he said.

“We were concerned about the softness of the Franka limestone,” the architect went on to say. “However, by working with the fabricator and the testing lab we were able to increase the thickness of the stone to achieve the desirable stone sizes which were mechanically supported to the concrete facade.”

According to Phillips, the design team was introduced to many fabricators in Malta. “They are more like artisans,” he said. “They showed us how they hand carve heavy pieces of stone. They sculpt the stone. I think it is a much better look. The handcrafting is interesting and better displays the craft of stone work than machined blocks.”

“There were stone engineers that put together mock-ups on site,” the architect went on to explain. “We couldn’t polish the limestone because it was too soft, but it could be honed, split-face or rock-face. The rock-face was selected as it represented nicely the way stone is used in Malta.”

Additional consideration had to be given to how many installers would be needed for the project and the best method to install the limestone. “We did a sealed facade instead of open joints,” said the architect. “The sealant was very critical, as it could bleed into the stone and discolor it. That’s why we used a silicone sealer that was tested on the limestone to prevent this.”

Joints were sealed with Sika Sikasil WS-355 sealant and the stone was sealed with Sika Conservade-5 sealant. The stone pieces were secured to the concrete building with a mechanical anchor system.

Extending the stone palette

In addition to Maltese limestone, a variety of stone from Egypt as well as other countries was also chosen for the design of the 98,000-square-foot facility, which sits on nearly 10 acres. “We utilized other stone that came from Egypt,” said Phillips. “We chose stone from quarries in the Sinai area.”

Complementing the Franka Rockface limestone base of the facade is Egyptian Galala Classic limestone with a honed finish and polished Imperial Red granite. For the flooring and monumental stair in the atrium of the office building, a combination of Sunny Light and Khatameya (Sahara Beige) marble — both from Egypt — and Rojo Alicante marble from Spain were employed. The wall behind the monumental stair features Frank Rockface limestone and honed Galala Classic limestone. Moreover, the countertops in the common bar area in the office building and entrance building are fabricated from Anarello Capri limestone.

The design team chose the stone varieties because they complement Valletta’s landscape and vernacular architecture. The site plan is organized around Bronze Age and Roman archeological remains that were discovered during excavations. “The building sits on an old archeological site,” explained Phillips. “We had unearthed burial chambers carved into the limestone strata.” A central stone garden features several of the rare structures.

Approximately two-thirds of the site is designed as a xeriscape — with the remainder utilizing native plant species adapted to minimum water consumption. Large underground cisterns capture rainwater on the site for irrigation and other non-potable uses. “There is a good marriage between the building and the landscape,” said the architect.

The design of the U.S. Embassy Compound began in late 2007 and construction commenced in 2008. The facility was ready for occupancy by July of this year.     

                                      U.S. Embassy Compound

Valletta, Malta

Architect: Karn Charuhas Chapman & Twohey (KCCT) Architects, Washington, DC

General Contractor: American International Contractors, Inc. (AICI-SP), Arlington, VA

Landscape Architect: Rhodeside & Harwell, Alexandria, VA

 

Did you enjoy this article? Click here to subscribe to Stone World 

Recent Articles by Jennifer Adams

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

The Stone Fashion Show at Marmomacc in Verona

As usual, stone suppliers from Italy and around the world relied on the Marmomacc fair to showcase some of the latest stone materials to the international marketplace. The following is a look at just some of the stone materials on display in Verona.

Stone World Magazine

Stone World September 2014 cover

2014 September

In this issue of Stone World, we have a Report from Europe, which includes a series of articles about the quarries and stone processing operations that SW editor Jennifer Adams visited as part of the Marmomacc Stone Academy.

Table Of Contents Subscribe

Contemporary Stone & Tile Design Magazine

CSTD Fall 2014 cover

2014 Fall

In this issue of Contemporary Stone & Tile Design, we take a look at the latest developments in TPT, with a feature article and you can read more comments from Waldrep on this subject as well as other industry professionals.

Table Of Contents Subscribe

STONE STANDARD

Are you aware of the new stone standard – ANSI/NSC 373 Sustainability Assessment for Natural Dimension Stone?
View Results Poll Archive

The Stone World Store

How_To_Polish_&_Restore_Mar.gif
How to Polish & Restore Marble Flooring

This video will show you step-by-step how to resurface and polish marble flooring from grinding and removing lippage and scratches to achieving a highly reflective polish.

More Products

Stone Guide

2014 Stone World Stone Guide

The directory for Stone, Equipment and Supplies - the single information resource readers turn to.

Stone Industry Education

stone industry educationStone Industry Education is sponsored by Stone World Magazine and Marble Institute of America. The SIE events will help you: strengthen your skills, build your business, and  increase profit in your shop.  Check out stoneindustryeducation.com to register for upcoming fabricator and installer seminars.

STAY CONNECTED

facebook logo Twitter  YouTubeGoogle+